The Next Big New Replace Window Pane Industry > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is a nuisance. It can also be a chance to upgrade your glass to energy efficient or insulated windows to enjoy benefits such as greater comfort, a higher the value of resales and lower utility costs.

You can do it yourself for a only a fraction of the cost it would cost to hire an expert. You only need the right tools and a few hours of your time.

Glass

If your single pane windows are old damaged, cracked or deteriorating replacing them with more modern glass that is tempered or insulated can increase energy efficiency and decrease noise while maintaining the historical integrity of older homes. A majority of homeowners with hand tools can repair a window pane. You will also need an additional window pane, glazier's suggestions, pliers, and latex glaze putty. If needed you can use a heatgun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass could cause serious injuries.

Take away any broken window replacement glass pieces that remain. This is best done using pliers, but a flathead screwdriver can also be used in the pinch. Then, use a wooden chisel or putty knife to take the remainder of the old putty from the frame and the sash. Be careful to not scratch the window sash. Work slowly and carefully. It is best to do this using a sturdy ladder instead of the ground and to have someone standing below the sash in order to help hold it steady.

Once you have removed all the old putty, you can prepare the Window Double Glazing Replacement frame to fit the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of width and height. Take these measurements to an hardware store or home center, and get a piece of stock glass cut to size. Alternately, you can cut the glass yourself if have the appropriate tools.

After putting in the new glass After installing the glass, apply a small amount of caulking to the edge. This will make the glass weatherproof. Install a glazier's pointing on both sides of the frame. This will secure the pane. The points shouldn't be so tight that they cause friction between the sash and the frame however they shouldn't be too loose.

Before applying the putty on the surface, knead thoroughly until it is soft and free from lumps. Make it into pencil-sized strips. The first strip should be placed in the corner of the frame, working from one corner to another to ensure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of steel which help to secure glass into frames for windows without scratching or damaging the delicate surface. Knowing how to use these hidden tiny pieces of help is simple and could save you money on professional installation or the cost of replacement windows uk of new glass.

After the old putty and glazier's points are removed Clean the frame thoroughly with a utility knife to eliminate any remaining residue. Lightly sand the wood in the rabbet grooves, if necessary, to smooth rough areas. If you sand wood, protect it with painter’s tape to protect it from damage caused by accidental sanding.

Write down the exact dimensions of the frame. Bring these measurements to a hardware store or home center and have the new pane cut smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new window in the frame and push it into place firmly with your hand. Use the chisel's point, or the edge of the putty blade to tap the glazier's points as shown in Figure 11. The glazier's points should be aligned with the top edge of your pane and the shoulders raised should be just below that lip.

Apply a thin bead of glazing compound on the edges of the new glass and into the rabbet grooves to seal and protect them. Let it dry completely and cure.

Install the new window sash when the glazing compound has dried. First, coat the wood with an even layer of linseed. This will prevent the new putty from drying out and cracking when it absorbs moisture. Apply the coating using a brush this coat, or the tip of the putty blade. Then, use the chisel on the back of the tool or the back of the putty handle to gently hammer the new sash or glazier's tip into the grooves of the rabbet. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown by error or a branch falling can result in a cracked or cracked window. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in the position with a tiny metal clip, called a glazier’s point and putty. This compound is also referred to as glazing compound. Before installing a new pane, first get rid of the old one and clean the area using a rag and a pull-type paint scraper or a wood chisel. Wear protective glasses and gloves while doing this work. You'll require a heat gun when the window is fixed to the frame.

If you're planning to replace the original sash, take off the mold that holds the old pane. Then sand the sash to ensure it's level and ready for new caulk. After the sash has been re-installed, apply a new silicone caulk around the glass to ensure that it doesn't swell or fade as time passes.

Take the glazing points out of the rabbets, the grooves in the sash where the glass sits. If they are hard to chisel, use an instrument such as a heatgun over them for a few minutes to soften them. When using a heated tool, be sure to not damage the sash and its railings.

After the old points of glazing and putty have been removed, make a bed for the new pane. Roll a rope of glazing compound between your hands, shaping it to be around 1/2-inch thick. Then, you can press it into the rabbets in which the glass will be. It is essential that the glass rests against the putty on both sides, so if you need to, lightly tap the glass into the rabbet using your thumb.

If the new pane is cracked, you can cover it with a solvent-based glass glue or silicone caulk before pressing it into the sash. If the crack is not sealed, you'll need to use putty to keep water from getting in. Once the putty is dry, wipe the oily film from the glass and allow it to dry completely before you paint. If you paint before the putty is fully dry, it won't create a strong seal and may be leaking or discoloring over time.

Paint

If you've had a broken window pane, you may be worried about the expense of replacing it. But the truth is that replacing a single glass pane doesn't have to break the bank if you do it yourself. In fact, even a double-pane window can be replaced at only a fraction of the cost of an expert.

First, if you are working on a large-sized window, make sure that it is securely fixed to the frame. With the right tools and techniques you can accomplish this task fairly easily and quick.

If you're ready to begin with the removal of the old window by removing the glazing points made of metal that are connected to it. They are basically tiny metal triangles that function as "nails" that keep the window in place within the frame of wood. They are submerged beneath a layer of glazing putty that is then cured to form a solid, molded wedge that secures the window in place and conceals the points.

After you have removed the old pane taken away clean the surrounding frame and wood. Scrape away any paint and sand down the rabbet grooves where the glazing points used to be. Sand them down to bare wooden surfaces, allowing you to paint the frames the same shade. After sanding the wood you can apply a layer flax oil. This will help prolong the life of the frame.

Next, measure the width of the window's opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass in times of seasonal change. Take these measurements to the hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.