Use What Is Billiards To Make Somebody Fall In Love With You > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

The rest is just technique -- locating and recognizing the state of each pin stack, manipulating the pins, applying torque to the plug. See Figure 1. (In practice, the cuts are produced by stacking pin segments of particular lengths, not by actually cutting the pins; hence the term "pin stack.") With no key in the lock, all the pin stack cuts rest within the plug. All three table sports are fun to play. Billiards and pool are often played on a seven-foot to eight-foot table. Well, now, look: we’re going to take an intermission for five minutes in case any of you have to leave, or are tired, or bored. Typical commercial and residential locks have five or six pin stacks (although four and seven aren't unheard of), with from four to ten distinct cut depths used on each. See Figure 2. The plug will be blocked from rotating if any pin stack is lifted either not far enough (with the cut still in the plug below the shear line) or too far (with the cut pushed above the shear line and into the shell); to rotate, all pin stacks must have a cut at the shear line.

Pin tumbler lock picking consists of raising the cuts on each pin stack to the shear line, one by one, until the plug turns freely. The basic design consists of a rotatable cylinder tube, called the plug, linked to the underlying locking mechanism. The plug/shell border is called the shear line. The height (or cut depth) of a key under each pin stack position is called its bitting; the bitting of a key is the "secret" needed to open a lock. When a key is inserted into the keyway slot at the front of the plug, the pin stacks are raised within the plug and shell. But the important thing, I repeat, about this kind of chant is that it’s quite different from the ordinary religious exercise that, say, we have in our churches, where we are interminably talking and thinking, and we never get to contemplation. You’ll find, therefore, that if you get with reality, all sorts of illusions disappear.

And in this way one is unrestricted, and one has voluminous pockets in which all sorts of things can be put if necessary. A key that is bitted to the wrong depth in even one pin position will not operate the lock. These imperfections are very small -- as little as .0001 inches in some cases -- but they are what allow us to manipulate ("pick") locks open without using the correct key. These locks are specially pinned to facilitate a more step-by-step approach. However, because the precision with which locks can be manufactured is limited by physical processes, materials, economics, and usability considerations, exploitable weaknesses almost always exist in practice. Picking depends on weaknesses in the implementation of locks -- small manufacturing imperfections -- rather than fundamental, abstract design flaws that would be present no matter how carefully made the locks might be. So, you see, we’re always passing the buck and don’t realize that the past is caused by the present as the wake of a ship flows back from the prow. So don’t try not to think. It follows gravity. So, very gently, would you try the experiment of allowing your breath to fall out.

In particular note that because the pins are slightly out of alignment, as the plug is turned gently, only the pin stack that is most out of alignment actually prevents further rotation. The principles and skills of lock picking, once mastered, can be applied against the vast majority of commercial pin tumbler locks, and the basic tools, if somewhat unusual, are quite simple. A few basic tools are sufficient to pick the majority of commonly used locks. Spring steel or stainless steel, between .020 and .035 inches thick, are typical materials. In the locked state the plug is prevented from rotating by a set of movable pin stacks, typically under spring pressure, that protrude from holes in the top of the opening in the shell into corresponding holes drilled into the top of the plug. Learn what a pin in that state feels like. Although combination lock manipulation exploits some of the same kinds of imperfections as pin tumbler lock picking, the principles and techniques are quite different and are well beyond the scope of this document. Picking tools are designed to perform one of two basic functions: manipulating pins and turning the plug. Good tools are important, to be sure, but once a few basic tools are available the student of lock picking is usually better off investing in new locks on which to practice rather than in new picking tools.

If you cherished this article and also you would like to get more info concerning what is billiards please visit the page.