5 Clarifications On Replace Window Pane > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is an issue. It can also be a chance to upgrade your glass to energy efficient or insulated windows, and reap benefits like greater comfort, a higher the value of resales and lower utility bills.

This is a project you could take on yourself for a fraction of the cost of hiring an expert. It requires the right tools and only an hour or two of your time.

Glass

If your single pane windows are old broken, deteriorating or damaged replacing them with more modern insulated or tempered glass can increase energy efficiency and decrease noise while also preserving the original character of older homes. Most homeowners with basic hand tools can replace Window Pane a window pane. Alongside a replacement pane, the following tools are required for the replacement process: latex glazing putty Glazier's points; pliers and an electric heater to warm the old putty, if needed. Wear safety glasses and gloves before you begin. Working with broken glass could cause serious injuries.

Take away any broken glass pieces remaining. It is best to use pliers for this however, a flathead may work equally. Make use of a wood chisel or putty knives, to take away any old putty remaining around the frame and the window sash. Take your time and work slowly making sure not to damage the old window sash. This is best done on an elevated ladder, not on the ground. Also, you should have someone on the ground to ensure it is held steady.

Make sure the window frame is ready to accept the new pane once you have removed the old putty. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of the width and height. Take these measurements to the nearest hardware store or home center and get a piece of stock glass cut to size. You can also cut the glass by yourself if you have the appropriate tools.

After installing the new glass Apply caulking to the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to secure the pane in its place. The points should not be so tight that they create friction between the frame and the sash however they should not be loose.

Before applying the putty knead it thoroughly until it's soft and free of lumps. Then, roll it into pencil-size strips. Place the first strip to the corner of the frame, working from one corner to the other so that it is smooth and even.

Glazier's Points

The glazier’s points are small triangular pieces of steel that help secure the glass into the window frame without causing damage to the delicate surface. It's simple to learn how to use this hidden tool and you can save money on the expense of an expert installation.

After the old putty and glazier's points are removed and the frame is thoroughly cleaned using a utility knife to eliminate any remaining traces. Lightly sand the wood into the rabbet grooves, if necessary, to smooth out rough areas. If you sand wood, cover it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and write down accurate measurements. These measurements can be taken to an hardware or home centers store, and the new frame will be cut a bit smaller. This will ensure that the pane fits snugly and allows for expansion and contraction.

Place the new pane into the frame and press it down with your hands. Then, use the tip of your chisel or back of the putty knife to make a tap on the glazier's facets, as shown in Figure 11. The glazier's points should be flush against the top edge of your pane, and the shoulders raised should be just below the lip.

Apply a thin layer glazing compound on the rabbet grooves as well as the edges of the glass. This will protect and seal the edges. Allow this to dry and cure completely.

After the glazing compound dries it's time to put in the new window sash. First, saturate the wood with a heavy coat of Linseed oil. This will stop the new putty from drying out and cracking due to the moisture it absorbs. Apply this coat using a brush or the tip of your knife, then employ the chisel or back end of the putty knife to gently hammer in the new sash and glazier's point into the grooves of the rabbet. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball that is thrown or a rock that is errant or falling branch could cause a window to break or crack. Luckily, most windows can be replaced by simply putting a brand new piece in the proper place. The glass is held in place using tiny metal clips known as the glazier's pointed and putty, often called glazing compound. Before you install a new pane, first get rid of the old one and clean up the area with an abrasive and replace Window pane a pull-type paint scraper or the wood chisel. Wear gloves and safety glasses when you work. You'll need a heating gun if the window handle replacement is glued into the frame.

If you plan to reinstall the original sash, remove any molding pieces that hold the old pane in place. Sand the sash until it is flat and ready to receive new caulk. After the sash has been re-installed, apply a new silicone caulk around the glass to ensure it won't leak or discolor in time.

Remove the glazing points from the rabbets, or the grooves in the sash that the glass sits. If they're difficult to cut out, you can try holding the hand tool, such as a heat gun over them to soften them before you do. When using a heating tool, make sure to avoid damaging the sash and its railings.

Prepare the bed for your new pane after you have removed the old glaze points and putty. Roll a piece of glazing compound between your hands, shaping it to be around 1/2-inch thick. Press it into the rabbets, where the glass will be placed. The glass must rest against the putty on both sides. If necessary gently tap your glass into the rabbet with your thumb.

If the new pane is cracked, you can cover it with a solvent-based glass glue or silicone caulk before pressing it into the sash. If the crack is not sealed, you will need to apply putty to keep water out. After the putty is dry then clean the oily film off the glass using a rag and allow it to dry completely before painting. If you paint before the putty has completely dry, it won't create an effective seal and could leak or discolor in time.

Paint

You might be worried about replacing a broken pane of glass. It's true that replacing a single pane of glass doesn't have to be expensive when you do it on your own. Even a double glazed windows replacement-paned window can be replaced for a fraction of what it costs an expert.

If you are working with a large glass window, first make sure it is securely attached to the frame. This can be done relatively easy and quick with the appropriate tools and techniques.

When you are ready to start with the removal of the window pane. Remove the metal glazing points that are attached to it. These are tiny metal triangles which act as "nails" that hold the window within the frame. They are placed under a glaze putty or bead that sets to form solid wedge that holds the frame in place and hides the sharp edges.

Once you have the old pane removed clean the surrounding frame and wood. Scrape away any old paint and sand down the rabbet grooves where the glazing points used to be. These should be sanded to bare wood to allow you to paint them the same shade as the rest of the frame. After sanding the wood you can apply a layer flax oil. This will help extend its life.

The next step is to measure the dimensions of the window opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get a precise size for the new pane. This will also allow for expansion and Replace window pane contraction of the glass in times of seasonal change. Take these dimensions to your local hardware or home improvement store, and they will have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.