You'll Never Be Able To Figure Out This Replace Window Pane's Secrets > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can cause a lot of trouble. It could also be a chance to upgrade your glass to energy-efficient or insulated windows and benefit from more comfort, higher the value of resales and lower utility bills.

This is a project you could take on yourself for a fraction of the cost of hiring an expert. You only need the right tools and a few hours of your time.

Glass

If your single-pane windows are old broken, deteriorating or damaged replacing them with more modern glass that is tempered or insulated will improve energy efficiency and reduce noise while preserving the original character of older homes. The procedure of replacing the replacement window glass near me pane is easy and can be completed by anyone with basic hand tools. You will also require an additional window pane, glazier's suggestions, pliers, and latex glaze putty. If you need to you can use a heatgun to warm the old putty. Wear safety glasses and gloves prior to starting. Working with broken glass could cause serious injuries.

Begin by removing any broken pieces of glass windows replacement. It is best to use pliers however a flathead could work equally. Then, use a wood chisel or putty knife remove the rest of the old putty around the frame and sash. Be careful and slow making sure not to break the current window sash. This should be done on an elevated ladder, not on the ground. Also, ensure that someone lower to hold it steady.

Make sure that the window frame is ready to receive the new pane after you have removed the old glue. Take measurements of the width and height of the opening in the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to the nearest hardware store or home center and have a piece of stock glass for window Replacement cut to size. Alternatively, you can cut the glass yourself if have the appropriate tools.

After putting in the new glass After installing the glass, apply some caulking on the edges. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points shouldn't be so tight that they cause friction between the sash and the frame however they shouldn't be loose.

Before putting the putty on, work it in a gentle manner until it is soft and free of lumps. Roll it into pencil-sized strips. The first strip should be placed to the corner of the frame, moving from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier's points are small triangular pieces that help secure glass into a window frame without scratching or damaging the fragile surface. Learning how to use these little helpers is easy and could save you money on a professional installation or the cost of buying new glass.

After the old putty as well as the glazier's point are gone and the frame is thoroughly cleaned with a knife to eliminate any remaining residue. Lightly sand the wood into the rabbet grooves, if necessary, to smooth rough areas. If you decide to sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and record precise measurements. Take these dimensions to a hardware store or home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a secure fit and leave room for expansion and contraction.

Place the new pane into the frame and press it into the frame with your hand. Utilize the point of the chisel or the back of the putty blade to tap the glazier's points, as shown in Figure 11. The glazier's points should be flush against the top edge of your pane and the shoulders should be just below the lip.

Apply a thin layer of glazing compound on the edges of the new glass and in the rabbet grooves to seal and protect them. Let it dry completely and cure.

Install the new window sash when the glazing compound has dried. First, you need to coat the wood with a thick layer of linseed. This will stop the new putty from soaking up moisture and deteriorating and cracking with time. Apply the coat using a brush or the tip of your putty knife, then use the chisel, or the back end from the putty knife to gently hammer the new sash and glazier's points into the grooves of the rabbet. Repeat this procedure every 10 inches along the frame's perimeter.

Putty

A baseball thrown at you, an errant rock or a falling branch can cause a window pane to crack or break. The majority of windows can be replaced easily by putting in a new piece. The glass is held into the position with a tiny metal clip, also known as a glazier's point and putty. This compound is also known as glazing compound. Before you install a new pane, first remove the old one and clean up the area with a rag and an abrasive scraper that is a pull type or a wood chisel. Wear protective glasses and gloves while working. If the window is attached to the frame, you'll need to use a heat gun to soften the adhesive before taking it off.

If you are planning to reinstall your original sash, remove the molding that supports the old pane. Then you can sand the sash down to make sure it's flat and ready to be re-caulked. Once the sash is installed, you can apply a silicone caulk over the glass. This will ensure that it won't be leaking or fade over time.

Remove the glazing points in the rabbets. These are the grooves in the sash, where the glass replacement window is located. If they're hard to cut, place the hand tool, such as a heatgun over them to allow them to soften before. If you're using a heated gun, make sure not to scratch the railings of the sash or the sash itself by placing the tool too closely.

Once the old points of glazing and putty have been removed, prepare a bed for the new pane. Roll a piece of glazing compound between your hands, and form it to be about 1/2-inch thick. Then, press it into the rabbets where the glass will sit. The glass should rest against the putty on both sides. If needed gently tap your glass into the rabbet using your thumb.

If the new pane has a crack you can fill it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. Otherwise, you'll need to apply putty on the crack to form a tight seal and keep water out. After the putty has dried clean the oily film off the glass and let it dry completely before painting. If you paint before the putty is fully dry, it won't form an effective seal and could discolor or leak over time.

Paint

If you've experienced a broken window pane, you may be concerned about the expense of a new one. The truth is, replacing a single piece of glass doesn't have to be costly even if you do it your own. In fact windows with double panes can be replaced for a fraction of the cost of a professional.

First, if you're working on a large window pane replacement, ensure that it is securely attached to the frame. This task can be made relatively simple and quick with the right tools and techniques.

When you are ready to start, remove the old window pane. Pry out the metal glazing points that are attached to it. These are basically small metal triangles that act as "nails" that hold the window in in the wood frame. They are submerged beneath a bead or glazing putty which hardens into a solid wedge that holds the frame firmly in position and hides the sharp edges.

After removing the old pane, clean the frame and wood. Scrape off any paint that has been used and sand down the rabbet grooves in which the glazing points were placed. Sand them to bare wooden surfaces, allowing you to paint the frames with the same color. After the sanding process, apply a coat of flax oil to the bare wood to prolong its life.

Next, measure the width of the window's opening. You'll need to determine the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. You can bring these measurements to a hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.