Ten Replace Door Lock Products That Can Make Your Life Better > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first line of defense is your door lock. It will stop unauthorized entry into your home. The signs of wear and tear and even instances such as moving into a new home or burglaries, could trigger the necessity of replacing patio Door lock your lock.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will assist you purchase the right-sized lock.

Deadbolt

Installing a deadbolt is ideal way to secure your door from burglars. When the bolt is extended into the strike plate of the doorframe it makes it more difficult for an intruder to get through the door. A single-cylinder deadbolt is activated using a key on the exterior, and the thumb-turn mechanism that is located inside. A deadbolt will only work when it is properly installed.

You will first need to determine if the upvc door lock replacement has an existing hole for a deadbolt, or if you'll need to drill it out. With the template included with the lock installation kit mark the spot of the deadbolt's hole on the door's surface. Then, use your tape measure to determine how high the deadbolt needs to be. Then, mark this height on the side of the door and use a speed square to draw an even line across the mark you made for the bolt hole.

Next, use a power drill to bore this area until the hole is on the opposite side of the upvc door replacement lock. It could take a few minutes. Sand the hole and edge of the door to make it smooth. It's also recommended to paint or stain the door at this point.

When the door is open take off any screws visible on the existing deadbolt. This will reveal the front and back assemblies of the deadbolt and also the bolt that is inside. Then, unscrew the bolt and replace it with a brand new bolt that matches your door hardware. The bolt is typically connected to a set plate, which you will need to unbolt. Then, you'll need to chisel the area on the door frame to accommodate the strike plate.

If your strike plate is out of alignment, it could be because the previous installer did not mortise it properly or that a weatherstripping changed the strike's location. To correct this issue, you will need to remortise both the strike plate and the deadbolt. Close and lock the deadbolt once you've completed this process. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

It can make your home and business less secure when the door knob is worn. It can make opening or closing the door more difficult, so it is an ideal idea to replace it. It shouldn't take longer than 30 minutes. You can use a screwdriver as well as pliers to remove the old knob or handle, but be careful not to scratch any of the other components on the door.

Spray WD-40, or another dry lubricant on the mechanism of your door knob prior to you begin. This will help the new lock slide smoothly as you turn it. To ensure proper operation, it's important to choose a knob and handle that are compatible with your doors. If you don't already have a doorknob that matches then you'll have to buy a replacement.

Before you begin the replacement, examine the old knob to determine which screws are keeping it in place. If there aren't any screws, you can use a screwdriver to wedge between the cover plate and the plate with hidden screws and pop it off.

Once you've removed the knob that was previously used, look it over for signs of damage or rust. If the knob is damaged or has marks or scratches it's time cost to replace upvc door lock mechanism clean it. Otherwise it shouldn't need any major work.

It's time to install the new one. First, examine the two new knobs to ensure that you're choosing the right one for your door. You should select one with an extending rod designed to interlock with the second knob's rod mechanism. After you've placed the new knob into the hole and then put it in the latch.

Thread the latch plate screws downwards, then test the spring by pushing down on it repeatedly. The latch should pop up each time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob into the cylinder holes on the exterior knob and secure it in place.

Latch

A latch is a steel piece that extends into the doorjamb to secure it shut. The latch can be operated by a handle or knob on the interior of the door, or a thumb-turn on the outside. A deadbolt is a device used to secure a latch and keep burglars from piercing the glass of the door. It also offers protection from the accidental or deliberate closing of the door by children or pets. A latch can be installed with a single cylinder deadbolt or a double cylinder deadbolt, according to the security level you prefer.

Installing a deadbolt is the same as installing a latch, however, there are some distinctions. To ensure that the new lock will work first, you must measure the setback on the doorjamb using a tape measure. The setback is the distance between the edge of the doorjamb to the middle of the hole for the latch faceplate. The standard setback is 2 3/8 to 2 3/4 inches. If you have a larger setback, you may need to purchase a larger latch from a hardware shop or locksmith.

Next, drill a hole for the latch plate in the edge of the doorjamb. Utilize a chisel to chisel the latch mortise. Make sure that the depth is sufficient for the faceplate to be in line with the doorjamb. Tape the strikeplate to the doorjamb to ensure it is positioned properly.

If the strike is too high, you can push the door back or apply pressure using an iron tire or crowbar. This can also crack the doorjamb. To correct this issue, the strike can be lowered by drilling a new hole through the doorjamb, and then chiseling out the core of the old hole.

Installing the new strike plate is the last step. This can be accomplished by screwing the new plate over the existing screwholes. Use wood putty then to fill in any existing screw holes or bolt holes which aren't going to be used. After the putty is dry you can sand it until it has a smooth finish.

Strike

The piece of metal that is inserted between the deadbolt and latch when the door replacement door locks is closed is an electric strike. It is an essential component of the lock's overall safety, as it prevents the door from opening, and also provides additional resistance to force or kick. If a door comes with an electronic strike, it can be opened only by an entry key and a control unit that controls its electrical impulses.

In the past, installing an electronic strike was as simple as cutting a portion of a doorjamb in order to release the latchbolt of a cylindrical lock from the pocket that is inside the strike. This is not only unattractive, but also exposes the mechanism of the latchbolt and keeper to uninitiated users.

Recently, several electric strike manufacturers have created a brand new electric strike dubbed the "No Cut" strike that doesn't require a cutout in the doorjamb to function. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without marring the faceplate of the doorjamb.

The strike is fitted with an internal ramp that lifts the latchbolt and keeper whenever it receives a signal from an individual reader. The keeper and latchbolt are pushed up the ramp by the retract. When the door is shut the deadbolt remains in extended and the latchbolt is retracted into the keeper.

Installing an electronic strike is a simple procedure, particularly if you're replacing an existing strike. However, if you're upgrading cost to replace upvc door lock mechanism an electric strike for an access control system, you'll have to ensure that your new system is compatible with the kind of lock you have installed. It is also necessary to make sure that the strike is connected to your access control system and is configured to function in a fail-safe manner.

One way to protect against unauthorized access is to upgrade the strike on your doors to a high-quality strike plate. These plates are fitted with four to six screws of three inches instead of the two, three-fourth inch screws that are typically used in regular strikes. The longer screws make it more difficult for someone to break the frame and reach inside to turn the thumb turn piece of a single cylinder deadbolt.