The 10 Most Scariest Things About Door Lock Change > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive method to increase the security of your home. However, this process is not for all. It requires some expertise and patience.

It is necessary to replace the cylinder, which is inside the knob's body. The cylinder is responsible for recognizing the key as it is inserted in the lock.

Removing the old lock

First, you must remove the lock you have been using for a while. This is a relatively easy procedure, but there are a few points to keep in mind. Make sure the new lock fits the door. This will ensure that it fits properly and does not create a gap around the deadbolt plug or latch.

After you have removed the latch plate, you'll be required to search for two screws or bolts in the casing's interior which are holding the casing in place with the two halves of the lock. Remove these screws using a screwdriver before removing the lock from the door. If you are using a mortise locking system, there is a set screw that binds the handle to the spindle. Remove the doorknobs by unscrewing this screw using the help of a screwdriver.

Take the deadbolt and latch plug from your door jamb. Install the new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the door's edge to ensure that the new lock will be able to fit.

Several reasons might prompt you to change your door lock, such as being concerned that someone else may have the key, or you are welcoming the arrival of a new roommate. You could save money if you take the lock off yourself instead of hiring an expert. The process is easier than most people think, and it can be done in a few minutes.

Start by removing the handle and trim from your door. Then, you can pry the trim away using a flat screwdriver. You should be able to twist off the majority of it. In some instances you may be able remove the handles completely. The next step is to look for a hole on the inside of the handle, and insert a straightened clip into it. This will trigger the release mechanism, allowing you to take off the handle. The next step is to look at the inside of the lock for another small tab, and then press it using a flat screwdriver. After the spindle is removed, you can then take off the cylinder and housing.

Selecting a new locking system

You have many options when it comes time to pick a new lock. Consider different types of double glazing window locks repairs, and find one that matches the style of your door. Consider the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Also, make sure to choose a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give an idea of their strength and the difficulty to pick them or disable them. A grade 3 lock may be a good choice for a tranquil rural apartment complex, while the grade 1 lock may stand up to the traffic near a busy store front on a city street.

Most smart door locks require a digital code to open. If you are worried about hacking, or any other security concerns, speak to an expert locksmith.

replace double glazing window locks repairs double glazing window locks replace upvc (henry-flanagan-2.mdwrite.net) the cylinder

If your door lock's cylinder is damaged or broken it can be replaced in a matter of minutes using a simple DIY project. The key is to select the correct cylinder and follow the directions that accompany it. First, remove the handle or knob if it is present. Then using a screwdriver take off the trim around the lock cylinder. After the trim is removed, you will be able to access the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently lifted out of the door.

Before you install the new cylinder, be sure it's the right length for the door you are using. With a tape measure, measure the distance between the center of the cylinder and the right and left sides. Then, purchase another cylinder that has the same measurements. This will stop the cylinder from snapping, which can occur when the door is kicked in or when the key gets stuck inside.

Install the replacement cylinder into the door and then turn the key. This will align the cylinder with your carrier which is located usually on the outside of the lock. Then, loosen the set screws that should be a couple of turns in the head. Also, you will need to loosen the screw at the door's edge that fastens the case, if there is one.

After you have removed the lock cylinder, you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder to the stem of the lock indicator that you can do by pulling up three small tabs on back of the cylinder using needle-nose pliers. Then, you'll be able to attach the second bracket to the back of the cylinder. Then, you must reinstall the strike plate and latch plate as well as the retaining ring connected to the top of the lock the cylinder.

Installing a new lock

Start by measuring the door's width if are replacing a lock that is already in use. Most residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is thicker you will require an extra-thick door kit that includes longer screws as well as longer tail pieces (for door knobs) or spindle extensions (for deadbolts).

Most locks come with comprehensive instruction booklet that will assist you in installing the new hardware. Before beginning, you must read the instructions to ensure you've followed all the steps. The manual will also give you an idea of the level of expertise required to perform the task. If you're changing a lock for the first time, you may consider asking a more experienced person for help.

Before installing the new lock it's an excellent idea to put cover the holes with tape the old hardware. This will stop the screws from falling out of the holes and safeguard any tile you may have put in the area. It also shields your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a piece of painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape in the event that you have it.

Once you've removed the screws that connect the inside of the lock section to the exterior side then pull it out straight away. It is important to do this quickly to avoid the lock from accidentally closing and damaging the mechanism.

Fit the new latch bolt in the upper cross bore of the new lock, if it comes with one. Make sure you place it in the correct place, which is usually indicated by an illustration on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate into the door jamb. Test the deadbolt a few times by throwing it to ensure it is extending into the strike plate. Follow the steps that come with your electronic smart lock to program it. This requires downloading an app and registering your email address, confirming your identity, and accessing the wireless network to connect your device.